We make the inside of the box.
Customized corrugated and chipboard products — partitions, die cuts and inserts — built on our own line in Fort Wayne to the part you actually ship.
General purpose. The stock most orders run on.
- Cells
- 20
- Cell size
- 3.48 × 3.98"
- Slots
- 12
- Board
- 3.22 ft²
Chipboard · 0.03" caliper · ships knocked down
Change the cell count and the drawing rebuilds. That is roughly what a changeover looks like on our floor — a setup change, not a new production schedule.
How we work
Built for the way your line actually runs.
Most packaging problems are really timing problems, storage problems, and parts arriving scuffed. This is how our line is set up to fix them.
Built to your design
Send us the part, not a guess at the dimensions. We build around what you actually ship, so parts stop moving and stop scuffing.
Quick changeover
Our line is set up for short runs. Changing cell count or board caliper is a setup change, not a production schedule, so small orders do not wait behind large ones.
Prototype to production
No minimum that makes a sample pointless. Prove the design on a short run, then release production.
Flat or assembled
Ship knocked down to save freight and floor space, or arrive assembled and ready to drop in.
What we manufacture
Customized corrugated products manufactured to your design.
A part that is close enough is a part that moves in transit. We build to your design — send dimensions, a print or a sample, and we work from that.
- Chipboard partitions, .022 through .050 caliper
- Corrugated partitions in B, C, and double wall
- Cell sizes from 1/4 in. to 60 in., heights to 24 in.
- Knocked down flat or delivered pre-assembled
- Die-cut corrugated inserts and components
- Pads, sleeves, layer sheets, and U-boards
- Short runs and prototype sets
Corrugated partition grid, assembled 
Die-cut corrugated sleeves 
Die board on a sheet of chipboard
| Stock | Caliper | Typical use |
|---|---|---|
| Chipboard, .022 | 0.022" | Light parts. Highest cell density per footprint. |
| Chipboard, .030 | 0.03" | General purpose. The stock most orders run on. |
| Corrugated, B flute | 0.125" | Cushioning for glass, castings, and machined parts. |
| Corrugated, C flute | 0.156" | Heavier parts and taller cells that need to stand up. |
| Corrugated, double wall | 0.25" | Maximum rigidity. Returnable and long-haul programs. |
2003
Established
Cutting board in Fort Wayne since.
60″
Largest cell
Down to a quarter inch at the other end.
24″
Tallest panel
Deep cases and standing parts.
Quick changeover
Small orders don't wait behind big ones.
Our line is set up so that changing cell count, board caliper, or panel height is a setup change measured in minutes. That is why a 200-piece order and a 20,000-piece order can run the same week.
Order lands
We confirm the design against your part.
Setup
Slitters, scores and dies reset to the new layout.
Run
Short runs go on the schedule, not into a queue.
Out the door
Local on our truck, or on a freight line the same week.
On the floor
The equipment your parts run on.
Die cutters, slotters, a folder gluer and the saws and slitters that set up every run — all in our Fort Wayne plant.
Clamshell die cutter with a sheet on the bed 
Flatbed die cutter 
Folder gluer 
S&S slotter 
Band saw 
Slitter sample table
For box manufacturers
We don't compete with your box supplier. We fill their boxes.
Corrugated plants build the box. We build what goes inside it. When a customer needs a partition or die cut their box maker doesn't run, we quote it, make it, and ship it to whichever dock the job needs — theirs or the end customer's.
2003
Short to production
1/4 in. to 60 in.
Flat or assembled
Send us the part. We'll build what goes around it.
Dimensions, a drawing, or the part itself — whichever you have. We quote from what you actually ship.